Question 1.
Which statements are true about a cascaded FICON topology? Select three.

A. It requires Fabric binding to be configured in all the switches.
B. Only one hope (ie:traversing 2 switchs) is supported.
C. Separate ISLs must be used dedicated to FICON traffic.
D. Two byte link addressing as defined in FC-SB2, is mandatory.

Answer: A, B, D

Question 2.
MDS3 _ 9509# install all system bootflash:m9500-sf1 ek9-mz.1.3.4.bin kickstart
bootflash:m9500-sfek9-kickstart-mz.1.3.4.bin
Verifying image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Verifying image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Extracting "sic"version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Extracting "ips" version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Extracting "system" version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Extracting "kickstart"version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Extracting "loader" version from image bootflash:/m9500-sf1ek9kickstart-mz.1.3.4.bin
[####################] 100% -- SUCCESS
Compatibility check is done:
Module bootable impact install-type reason
--------- --------- ---------- ------- ----- ---------
2 yes non-disruptive rolling
3 yes disruptive rolling Hitless upgrade is not supported
5 yes non-disruptive reset
6 yes non-disruptive reset
Images will be upgraded according to following table:
Module Image Running-Version Net-Version Upg-Required
--------- ------- ---------- ----------- ------ ----------
2 slc 1.3(4b) 1.3(4) yes
2 bios v1.1.0(10/24.03) v10.8(08/07/03) no
3 slc 1.3(4b) 1.3(4) yes
3 bios v1.1.0(10/24.03) v10.8(08/07/03) no
5 system 1.3(4b) 1.3(4) yes
5 kickstart 1.3(4b) 1.3(4) yes
5 bios v1.1.0(10/24.03) v10.8(08/07/03) no
5 loader 1.2(2) 1.2(2) no
6 system 1.3(4b) 1.3(4) yes
6 kickstart 1.3(4b) 1.3(4) yes
6 bios v1.1.0(10/24.03) v10.8(08/07/03) no
6 loader 1.2(2) 1.2(2) no
Do you want to continue with the installation (y/n)? [n]

What is the reason the upgrade would not be hit-less for the entire switch, above?

A. The supervisor module requires a BIOS upgrade, which is disruptive.
B. The "rolling-upgrade" for module 2 requires a second "slc" to be hit-less.
C. Module 3 is an IPS-8 card, which does not support non-disruptive downgrades.
D. Nodule 3 is an IPS-8 and the switch does not have a second IPS-8 card for route diversity 
    which could provide a "stable" upgrade.
E. No reason - the upgrade is non-disruptive and hit-less.

Answer: C

Question 3.
Which methods can be used to control Iscsi INITIATOR ACCESS TO VIRTUAL TARGETS? Select three.

A. Zoning
B. Specifying on which Gigabitethernet port the virtual target is advertised.
C. Setting up Iscsi PROXY MODE FOR THE INITIATORS
D. Specifying which IP subnet virtual target can be accessed
E. Enabling role-based access control.

Answer: A, B, C

Question 4.
In a scenario with three lSLs between two switches, a single host in VSAN 5 on switch A, and a single storage device on switch B in the same VSAN. 

What would be the effect on the lSLs if Flow based load balancing option was enabled in VSAN 5?

A. Each subsequent frame will use the least utilized link, based on FCC.
B. Each subsequent frame will use a different link.
C. All frames between source and destination would follow same link for given flow.
D. Flow based load balancing is not enabled for an individual VSAN.

Answer: C

Flow based load balancing : all frames between source and destination would follow same link for given flow.

Question 5.
Which organization produce standards related to SCSI, Fiber Channel or Fiber Channel protocol? Select two.

A. SNIA
B. T11 Committee
C. Cisco Systems
D. T10 Committee
E. T12 Committee

Answer: B, D

=> T11 for fiber channel, T10 for SCSI

Question 6.
What is the User-specified VSAN Ids range?

A. 1-4093
B. 2-4093
C. 2-4094
D. 2-4092

Answer: B
=> user-specific VSAN 2-4093

Question 7.
What can be configured on a FCIP Profile?

A. Max and Min bandwidth, peer-info, compression ratio
B. Passive mode, peer-info, compression ratio
C. TCP port number, sack-enable, Max and Min bandwidth
D. Sack-enable, TCP port number peer-info
E. TCP port number, write accelerator compression ratio

Answer: C
=> FCIP profile for TCP port, sack-enable, Max and Min bandwidth

Question 8.
A Brocade 12000 in its native corePID mode (1) is connected to VSAN 1009 on an MDS. 

What is the correct output of the "show vsan 1009" command?

A. vsan 1009 information:
    name: VSAN 1009 state:active
    interoperability mode:default loadbalancing:src-id/dst-id/oxid
    operational state:up.
B. vsan 1009 information:
   name: VSAN 1009 state:active
   interoperability mode:1 loadbalancing:src-id/dst-id/oxid
   operational state:up.
C. vsan 1009 information:
    name: VSAN 1009 state:active
    interoperability mode:2 loadbalancing:src-id/dst-id/oxid
    operational state:up.
D. vsan 1009 information:
    name: VSAN 1009 state:active
   interoperability mode:3 loadbalancing:src-id/dst-id/oxid
   operational state:up.
E. vsan 1009 information:
   name: VSAN 1009 state:active
   interoperability mode:Brocade Native loadbalancing:src-id/dst-id/oxid
   operational state:up.

Answer: D

=> interop mode 3 for Brocade 12000

Question 9.
What TCP feature reduces the chances of an oversized IP packets from being fragmented?

A. SACK
B. Extended ping
C. PMTU
D. Retransmit timeout
E. Send buffer size

Answer: C

Question 10.
In Raid 0+1 the loss of a single drive:

A. Does not affect the redundancy of the array
B. Reduces the array redundancy to that of a Raid level 0
C. Same level of redundancy to that of a Raid level 1+0
D. Reduces the performance of the array
E. Has no affect what so ever on the array

Answer: B

	Web www.certsbraindumps.com