Question 1.
LSC validation is failing on a new SCCP IP phone that you have just added to the Cisco Unified CallManager 5.0 cluster. No other IP phones are experiencing any problems with LSC validation. 

What can you do to help pinpoint the problem?

A. Check for security alarms
B. Verify that the authentication string is correct in the Cisco Unified CallManager device 
    configuration screen
C. View the SDI trace output
D. Use the Security configuration menu on the IP phone to verify that an LSC has been 
    downloaded to the IP phone

Answer:  D

Question 2.
Which three capabilities can't be configured if the default dial peer is matched? (Choose three.)

A. Set preference to 1
B. Invoke a Tcl application
C. Enable dtmf-relay
D. Set codec to G.711
E. Disable DID
F. Disable VAD

Answer:  B, C, F

Question 3.
When using trace output to troubleshooting a Cisco Unified CallManager 5.0 problem, how can you collect and view the trace files?

A. Configure the proper trace settings on the Cisco Unified CallManager Serviceability page and 
    then use the embedded RTMT tool to view the trace files
B. Configure the proper trace settings on the Cisco Unified CallManager Serviceability page and 
    download the RTMT plug-in from the CallManager Administration page to view the trace output
C. Download the RTMT plug-in from the Cisco Unified CallManager Serviceability page to view 
    the preconfigured trace files
D. Configure the proper alarms and traces on the Cisco Unified CallManager Administration page 
    and view the output with the RTMT plug-in

Answer:  B

Question 4.
You are troubleshooting why a user can't make calls to the PSTN. You are reviewing trace files and you found where the user's IP phone initiates the call but you never see the call go out the gateway. 

What is the next step in troubleshooting this issue?

A. Look in the SDL trace file to see if there is a signal to another Cisco Unified CallManager node 
    with the same time-stamp
B. Look in the MGCP trace file to determine which MGCP gateway the call was sent to
C. Look in the IP Voice Media Streaming APP trace file to see if an MTP was invoked
D. Look in the SDL trace file to see if there is a signal to anther Cisco Unified CallManager node 
    with the same TCP handle

Answer:  A

Question 5.
Exhibit:
 

Your work as a network engineer at ITCertKeys.com. Please study the exhibit carefully. 

Voice bearer traffic is mapped to which queue in FastEthernet0/2?

A. Queue 2
B. Queue 3
C. Queue 1
D. Queue 4

Answer:  A

Question 6.
Exhibit:
 

Your work as a network engineer at ITCertKeys.com. Please study the exhibit carefully. You have received a trouble ticket stating that calls to international numbers are failing. To place an international call, users dial the access code, "9," followed by "011", the country code and the destination number. After entering the debug isdn 1931 command on the MGCP gateway, you have the user attempt the call again.

Base on the debug output, what is the most likely cause of this problem?

A. The TON in incorrect
B. The circuit is not configured correctly or has a physical layer issue
C. Cisco Unified CallManaager is not stripping the access code before sending the call to the 
    gateway
D. The gateway dial peer needs to prefix "011" to the called number so the PSTN knows this is 
    an internation call
E. The user's CSS does not permit international calls

Answer:  A

Question 7.
You have developed a dial plan for Cisco Unified CallManager 5.0 solution. All the route patterns, partitions, calling search spaces and translation rules have been configured. Before starting up the system you wish to test the dial plan for errors.

Which Cisco Unified CallManager tool will simplify this testing?

A. Route Plan Report
B. Dial Plan Installer
C. Dialed Number Analyzer
D. RTMT Traces and Alarms

Answer:  C

Question 8.
You have just obtained a list of the following options:
all patterns
unassigned DN
Call Park
Conference
Directory Number
Translation Pattern
Call pickup group
Route pattern
Message waiting
Voice mail
Attendant console

What have you selected in order to produce this list?

A. Route Plan > External Route Plan Wizard
B. Control Center > Feature Services
C. Route Plan > Route Plan Report
D. Dialed Number Analyzer

Answer:  C

Question 9.
You have configured the Enable Keep Alive check under Trace Filter settings. 

How does this change the trace output?

A. It adds the IP address of the endpoint in hex
B. It maps the unique TCP handle for the endpoint to the MAC address of the endpoint in the 
    trace output
C. It adds the SCCP messages and all fields sent as part of that message
D. It adds TCP socket numbers between the endpoint and Cisco Unified CallManager for the 
    session

Answer:  B

Question 10.
When using trace output to troubleshooting a Cisco Unified CallManager 5.0 problem, how can you collect and view the trace files?

A. Configure the proper trace settings on the Cisco Unified CallManager Serviceability page and 
    download the RTMT plug-in from the CallManager Administration page to view the trace output
B. Configure the proper alarms and traces on the Cisco Unified CallManager Administration page 
    and view the output with the RTMT plug-in
C. Download the RTMT plug-in from the Cisco Unified CallManager Serviceability page to view 
    the preconfigured trace files
D. Configure the proper trace settings on the Cisco Unified CallManager Serviceability page and 
    then use the embedded RTMT tool to view the trace files

Answer:  A

	Web www.certsbraindumps.com