Question 1.
Which two features require or may require configuring a SIP trunk? (Choose two.)

A. SIP gateway
B. Call Control Discovery between a Cisco Unified Communications Manager and Cisco Unified
Communications Manager Express
C. Cisco Device Mobility
D. Cisco Unified Mobility
E. registering a SIP phone

Answer: A, D

Question 2.
Refer to the exhibit.
 
The exhibit shows centralized Cisco Unified Communications Manager configuration components for TEHO calls to U.S. area code J08 from the U.K. The PSTN access code for the U.K is 9 and 001 for international calls to the U.S. 

What should the TEHO-US route list configuration consist of?

A. First route group should point only to the U.K. gateway. The second route group should point To the U.S. gateway.
B. First route group should be only the local route group. The second route group should point to the U.S gateway.
C. First route group should point only to the U.S. gateway. The second route group should be the  local route group.
D. The TEHO-US route list should contain only the local route group. The globalized configuration means that the appropriate gateway will be elected automatically.
E. The \+!route pattern should point directly to the U.S gateway.

Answer: C

Question 3.
When Cisco Extension Mobility is implemented, how is the audio source for the MOH selected?

A. The audio source that is configured at the user device profile is selected.
B. The audio source that is configured at the home phone of the user is selected.
C. The audio source that is configured at the physical phone used for the Cisco Extension Mobility login is selected.
D. The audio source that is configured in the IP Voice Media Streaming parameters is selected.

Answer: A

Question 4.
In what Cisco solution is Simple Network-Enabled Auto Provision technology used?

A. Cisco Unified Gateway Duplication
B. Cisco UnifiedCallManager Redundancy
C. Cisco Unified SRST
D. Cisco Unified Call Survivability

Answer: A

Question 5.
Which method can be used to address variable-length dial plans?

A. Overlap sending and receiving.
B. Add a prefix for all calls that are longer than 10-digits long
C. Use nested translation patterns to eliminate inter-digit timeout
D. Use the @macro on the route pattern
E. Use MGCP gateways, which supportvariable-length dial plans

Answer: D

Question 6.
Refer to the exhibit.
To stream multicast MOH to the remote site across the WAN, what should the minimum value for the Max Hops be configured as?

A. 1
B. 2
C. 3
D. 4

Answer: B

Question 7.
Refer to the exhibit.
 
Which statement about the configuration between the Default and BK regions is true?

A. Calls between the two regions can use either 64 kbps or 8 kbps.
B. Calls between the two regions can use only the G 729 codec
C. Only 64 kbps will be used between the two regions because the link is "lossy"
D. Bothcodecs can be used depending on the loss statistics of the link, when lossy conditions are high, the G.711 codec will be used.

Answer: A

Question 8.
Refer to the exhibit.
When the user of a phone registered to the Cisco Unified Communications Manager places a call to 3001 when the SAF network is down, what happens?

A. The call fails.
B. The call is rerouted to the PSTN with the constructed PSTN number as +442288223001
C. The call is rerouted to the PSTN with the constructed PSTN number as 442288223001
D. The call is rerouted to the PSTN with the constructed PSTN number as 0002288223001
E. The call is rerouted to the PSTN with the constructed PSTN number as +0002288223001

Answer: B

Question 9.
Refer to the exhibit.
 
The HO site uses area code 650. The BR1 site uses area code 408. The long distance national code for PSTN dialing is 1. To make a long distance national call, an HQ or BR1 user dials access code 9, followed by 1, and then the 10-digit number. Both sites use MGCP gateways. AAR must use globalized call routing using a single route pattern. Assume that all outgoing PSTN numbers are localized at the egress gateway as shown in the exhibit.

What should the AAR group prefix be?

A. 9
B. 91
C. none
D. +
E. +1

Answer: A

Question 10.
When Cisco Extension Mobility is implemented, which CSS is used for calling privileges?

A. The user device profile line CSS combined with the device CSS of the physical phone used to log in the extension mobility user.
B. The user device profile device CSS combined with the line CSS of the physical phone used to log in the extension mobility user.
C. Only the user device profile device CSS is used
D. The combined line/device CSS of the physical phone is used to log in the extension mobility user.
E. The combined line/device CSS of the user device profile.

Answer: E

	Web www.certsbraindumps.com